|
|
CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES. ...more details
| Recall Reason |
EQUIPMENT |
| Recall Date |
OCT 24, 2007 |
| Model Affected |
HUMMER |
| Potential Units Affected |
121680 |
|
Recall Summary
CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.
|
|
Consequence
THIS CONDITION MAY CAUSE INADEQUATE SEALING AND LOSS OF ENGINE OIL, POSSIBLY RESULTING IN A FIRE.
|
|
Remedy
HONEYWELL WILL REPLACE THE AFFECTED OIL FILTERS FREE OF CHARGE. THE RECALL BEGAN DURING NOVEMBER 2007. OWNERS CAN CONTACT FRAM CUSTOMER SERVICE TOLL-FREE AT 1-800-890-2075.
|
|
Notes
HONEYWELL INTERNATIONAL, INC.
|
THE OIL PRESSURE SWITCH WHICH CONTROLS THE POWER TO THE ELECTRIC FUEL PUMP CAN FAIL. FAILURE IS DUE TO A MISSING RUBBER SEAL BETWEEN THE SWITCH AND THE WIRING HARNESS. THE MISSING SEAL ALLOWS CONTAMINANTS TO ENTER THE SWITCH CAUSING IT TO FAIL IN THE OPEN OR CLOSED POSITION. ...more details
| Recall Reason |
FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS |
| Recall Date |
SEP 01, 1994 |
| Model Affected |
HUMMER |
| Potential Units Affected |
2300 |
|
Recall Summary
THE OIL PRESSURE SWITCH WHICH CONTROLS THE POWER TO THE ELECTRIC FUEL PUMP CAN FAIL. FAILURE IS DUE TO A MISSING RUBBER SEAL BETWEEN THE SWITCH AND THE WIRING HARNESS. THE MISSING SEAL ALLOWS CONTAMINANTS TO ENTER THE SWITCH CAUSING IT TO FAIL IN THE OPEN OR CLOSED POSITION.
|
|
Consequence
IF THE SWITCH FAILS IN THE CLOSED POSITION, THE PUMP WILL CONTINUE TO RUN WHEN THE ENGINE IS OFF, DRAINING THE BATTERY. IF THE SWITCH FAILS IN THE OPEN POSITION IT WILL CAUSE POOR PERFORMANCE AND POSSIBLY STALLING.
|
|
Remedy
DEALERS WILL INSPECT THE VEHICLES FOR THE PRESENCE OF THE SEAL. IF THE SEAL IS MISSING, THE SWITCH WILL BE REPLACED AND A NEW SEAL WILL BE INSTALLED.
|
|
Notes
AM GENERAL CORPORATION
|
THE COATING USED TO PROTECT THE ACCELERATOR PEDAL SHAFT IS INCOMPATIBLE WITH THE BRONZE BUSHING THROUGH WHICH THE SHAFT PASSES. OVER TIME, AND IN THE PRESENCE OF A CORROSIVE ENVIRONMENT (WATER, ROAD SALT), THE SHAFT CAN CORRODE INSIDE THE BUSHING INCREASING THE AMOUNT OF FRICTION BETWEEN THE ROTATING SHAFT AND THE STATIONARY BUSHING. ...more details
| Recall Reason |
VEHICLE SPEED CONTROL:ACCELERATOR PEDAL |
| Recall Date |
MAR 12, 1996 |
| Model Affected |
HUMMER |
| Potential Units Affected |
3000 |
|
Recall Summary
THE COATING USED TO PROTECT THE ACCELERATOR PEDAL SHAFT IS INCOMPATIBLE WITH THE BRONZE BUSHING THROUGH WHICH THE SHAFT PASSES. OVER TIME, AND IN THE PRESENCE OF A CORROSIVE ENVIRONMENT (WATER, ROAD SALT), THE SHAFT CAN CORRODE INSIDE THE BUSHING INCREASING THE AMOUNT OF FRICTION BETWEEN THE ROTATING SHAFT AND THE STATIONARY BUSHING.
|
|
Consequence
A CORRODED ACCELERATOR PEDAL SHAFT CAN CAUSE THE ENGINE THROTTLE TO BIND AND NOT FULLY RETURN TO IDLE WHEN THE OPERATOR'S FOOT IS REMOVED FROM THE ACCELERATOR PEDAL INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.
|
|
Remedy
DEALERS WILL INSTALL A REVISED ACCELERATOR PEDAL AND SHAFT ASSEMBLY.
|
|
Notes
AM GENERAL CORPORATION
|
THE PASSENGER COMPARTMENT IS SEPARATED FROM THE ENGINE COMPARTMENT BY AN INSULATED ENGINE COVER. THE INSULATION INSIDE THIS COVER CAN RUB AGAINST THE FUEL RETURN HOSE RESULTING IN A FUEL LEAK. ADDITIONALLY, A WIRING HARNESS CAN ALSO WEAR THROUGH CAUSING INTERRUPTION TO SOME ELECTRICAL OPERATIONS, INCLUDING THE FUEL PUMP. ...more details
| Recall Reason |
FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS |
| Recall Date |
SEP 01, 1994 |
| Model Affected |
HUMMER |
| Potential Units Affected |
1300 |
|
Recall Summary
THE PASSENGER COMPARTMENT IS SEPARATED FROM THE ENGINE COMPARTMENT BY AN INSULATED ENGINE COVER. THE INSULATION INSIDE THIS COVER CAN RUB AGAINST THE FUEL RETURN HOSE RESULTING IN A FUEL LEAK. ADDITIONALLY, A WIRING HARNESS CAN ALSO WEAR THROUGH CAUSING INTERRUPTION TO SOME ELECTRICAL OPERATIONS, INCLUDING THE FUEL PUMP.
|
|
Consequence
FUEL LEAKING INSIDE THE ENGINE COMPARTMENT CAN RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION. FAILURE OF THE ELECTRIC FUEL PUMP CAN CAUSE POOR PERFORMANCE AND POSSIBLE STALLING CREATING A ROAD HAZARD WHICH CAN RESULT IN AN ACCIDENT.
|
|
Remedy
DEALERS WILL REPLACE THE RUBBER FUEL LINE HOSE WITH A SOLID STEEL LINES AND ROUTE THE LINE TO PROVIDE ONE INCH OF CLEARANCE TO THE COVER. ALSO, THE WIRING HARNESS COVER WILL BE REPLACED AND THE WIRING REROUTED TO GAIN SUFFICIENT CLEARANCE.
|
|
Notes
AM GENERAL CORPORATION
|
|